For those living in flats or working in offices with scarce space for bike storage, Clugs can be scattered about the place with abandon, ready for any and all bikes to store. I'd say a Clug would make for a handy bike-washing solution, if you are in an apartment situation and need an inconspicuous, low-cost and relatively theft-proof way to hold your bike vertical while washing. What's wrong with a hook, you say? The problem with ceiling hooks is that they need to go into something as well, and unless they are supporting the entire weight of the bike they won't hold the wheel solidly, so bikes can swing around. With the rear wheel on the floor, the Clug is only bearing a bike load of a few hundred grams to keep it vertical/horizontal. The removal transient force approximates the weight of hanging a 7kg bike from a ceiling-mounted Clug. In other words, you can insert a 1-2kg wheel complete with tyre into a clug and it will stay put indefinitely – a good solution for storing a turbo wheel, or a spare set for different uses, like gravel riding or Sunday best.

Clug Pro | road.cc Review: Hornit Clug Pro | road.cc

I'd say the Clug is the best solution I've tried for keeping bikes in tight spaces. Other solutions often need the bike lifting vertically or sideways to get a hook or arm of some sort engaged, whereas your bike goes straight in-out of the Clug. Cons: Each size is specific to a range of tyre widths, possible issue with deflating tyres over time, price One thing to note: the size of the Clug refers to actual tyre size, not simply stated tyre size, so it's important to actually measure yours as this can vary greatly depending on the width of the rim and the brand of the tyre. For horizontal use, a mudguard protruding below the centreline of the wheel might cause issues – a soft flap should be fine, a plastic or metal guard would be likely to jam or bend. Maybe experiment with height to get a good-enough hold below the hard mudguard on the exposed wheel section.

CLUG Hybrid Bike Storage- White/ Black

Firstly, and foremost: just because I rate the Clug 4.5/5, doesn't detract from other options. The review is circa 1300 words, basically explaining my rating. That's the Road.CC difference. We live with products for months, then offer our opinions. We don't regurgitate PR or base findings on a day or two's use.

HORNIT MTB Bike Holder CLUG MTB White - Black | Halfords UK

Those of you owning bikes weighing less than 7kg are explicitly advised not to try to use the Clug like a ceiling hook. It even says so on the box. All about the bulge The Clug Pro is very minimal, even claiming a drop in weight over the standard version, though even as an ardent weight weenie I cannot think why lighter would be an important factor here. Easy to fit Faff - the beauty of the Clug is that you can push a bike home with one hand, into a tight space, and be done. If you had to reach past (around?) your bike to do up a toestrap with both hands, that would be a faff. and if the space were tight, possibly impossible, or highly-likely to see your arms/hands covered in filth from your rim. Possibly cut to ribbons by your steaming-hot disc rotor too. Once installed, the Clug can be removed easily and relocated in a minute – the insert covering the screws pops out and away you go. Tight spaces It can also double as a coathook, bag hook, for a rake, electrical cords... the list is pretty much endless.The premise of the Clug is simple: it's a clip that grips your tyre. That's it. Screw to the wall, insert bike. Done. Pull bike out, ride. Obviously something based on tyre size is going to need to accommodate a wide range of widths, so the Clug comes in three sizes: Roadie (23-32mm), Hybrid (33-42mm) and MTB (43-62mm/1.8-2.5in). I've reviewed the Roadie and Hybrid sizes. In the box are the Clug, instructions, and two screws and plastic plugs, for use in masonry or plasterboard. As with any DIY, you should be aware of what you're drilling into, and depending on the size of bike and surface you could always opt for a more solid retaining mechanism such as spring toggles. Once the body of the Clug is drilled to the wall, the curvy insert snaps into place and you're done. What works